Rivet Nut / Nutsert Tooling
Hand - Pneumatic - Battery Rivet Nut Tools from Primary Fasteners

An occasional use rivet nut tool, complete with mandrels for M3, M4, M5 & M6 inserts in aluminium and steel M3 to M5, quick mandrel change, simple operation.

£30.00 each plus VAT & Carriage

An occasional use rivet nut tool, complete with mandrels for M3, M4, M5 & M6 inserts in aluminium and steel to M5, quick mandrel change, simple operation. Supplied in a plywood case and a selection of rivet nuts in each of the above sizes.

£39.00 each  plus VAT & Carriage

Kit comprising M6,M8,M10,M12 nose assemblies, convenient for difficult access.

Will set up to M12 in Aluminium and Steel, M10 in Stainless Steel. The insert is up-set by turning the rear handle, which will free turn on a ratchet when the pre-set stroke length is achieved.

Conversion kit for M5,6 & 8 riv bolts included

Cased tool includes space for fastener storage

£95.00 each   plus VAT & Carriage           

FAR KJ15-M8 Rivet nut tool

Single Size tool to insert M8 rivet nuts - ideal for vehicle components, general project work. Use a spanner to apply the mandrel, side handle to keep the tool steady

£21.50 each     plus VAT & Carriage

Complete with M4,M5,M6 and M8 mandrels, a compact tool to set up to M8 rivet nuts in steel.

Ideal for M6 rivet nuts in all materials where handpliers are too small to generate the required traction forces.

£70.00 each     plus VAT & Carriage
 

Complete with M5,M6,M8,M10 mandrels, a larger tool to set up to M10 in Steel and M8 in Stainless Steel nutserts. 

A centre drill aim assists in rapid spin on and spin off after setting

The nutsert tool is also supplied with nose assemblies for 5,6 & 8mm rivet bolts. Supplied in a plywood case

£107.00 each    plus VAT & Carriage
 

The KJ60 insert tool

Will set rivet nuts from M3 to M8 in Aluminium, Steel and Stainless Steel. The tool is a 2 trigger set up, allowing spin on when pressure is applied to the end of the mandrel, setting when the top trigger is pressed and spin off when the bottom trigger is pressed..

Front facing air inlets on swivel attachments.

£565.00 each  + VAT & Carriage

Replacement Mandrels £16.50 each + VAT & Carriage

The Avdel 7420 nutsert tool

A working range of M3 to M12 rivet nuts. The nutsert is spun on when pressure is applied to the end of the mandrel, and a single action trigger to set and disengage. A cycle time of 2.5 seconds. Rear facing air inlet.

Additional nose assemblies are available at £39 each set if ordered with tool to install other rivet nut sizes in the working range.

A UNC nose assembly is available for this tool

£740.00 each + VAT & Carriage     

Single trigger action, The pop nut tool is stroke control operated featuring a simple gauge system located above the tool trigger for simple stroke adjustment.

Quick change nose assemblies

Supplied with one size of nose assembly, additional sizes available.

£740.00 each + VAT & Carriage

The firebird is a cordless 12v battery powered tool,
supplied with M4,M5 and M6 nose assemblies, 1 battery and charger.

Weighing just under 2.5kg, this tool develops 13,000N traction force enabling up to 130 stainless steel rivet nuts on one full battery charge.

With a long and established track record, a high quality and effective installation tool

£585.00 each + VAT & Carriage